Solar Panels Producing Less? Why Your System Output Dropped
A step-by-step way to figure out why your solar output fell, using the pattern of the drop to point to the cause and the right fix.
When solar panels are producing less, the pattern of the drop usually points to the cause: a sudden fall to zero suggests a tripped breaker, an inverter fault or lost monitoring; one weak panel suggests a failed microinverter, optimizer or damaged module; and a slow decline across the whole system is usually weather, shade, dirt or normal aging. Sorting out which pattern you have is the fastest way to the right fix and the right person to call.
Use this guide as a diagnostic checklist.
Key takeaways
- First confirm production really fell; lost internet can make a working system look dead.
- NREL's 2018 O&M guide names inverter failure as one of the most frequent causes of performance loss.
- Normal aging is slow: NREL found a median 0.75% per year across commercial and utility-scale sites in 2024.
- Seasonal dips, especially in winter, are expected, according to EnergySage.
- Gather data before calling a pro; it speeds diagnosis and supports warranty claims.
Step one: are your solar panels really producing less?
Before chasing a problem, check that it exists. EnergySage noted in a 2019 explainer that perhaps the most common way an inverter "fails" is losing its internet connection. Your app can show zero while panels work fine.
Quick ways to confirm:
- Look at your utility meter or bill for exports on sunny days.
- Check the inverter's lights or screen for a normal producing status.
- Compare with the same month last year, not with a sunnier season. EnergySage's August 2025 repair guide stresses that winter dips are normal.
- Compare with your installer's estimate or a PVWatts estimate from the National Laboratory of the Rockies (formerly NREL) at pvwatts.nlr.gov.
If the monitoring is the problem, our guide to monitoring that stopped working will help.
Why solar panels are producing less: match the pattern to the cause
| What you see | Likely causes | First step |
|---|---|---|
| Whole system at zero on a sunny day | Tripped breaker, inverter off or faulted, grid outage | Check breakers and inverter status safely |
| App blank but meter shows exports | Lost internet or gateway issue | Restart router; reconnect device |
| One panel at or near zero | Failed microinverter or optimizer, connector, damaged panel | Note panel position; call installer |
| Same panels weak at the same time daily | Shade from trees or structures | Check roof at that time of day |
| Gradual decline over months | Soiling, growing trees, aging | Compare year over year; inspect |
| Sudden drop in one string | Wiring fault, ground or arc fault, damaged module | Professional inspection |
| Lower output during smoke or heat waves | Haze blocking light; hot panels | Usually wait it out |
Equipment causes: inverters, electronics and wiring
NREL's 2018 best-practices guide calls inverter failure one of the most frequent causes of PV performance loss. EnergySage's August 2025 repair guide adds that a sudden dip is often an inverter issue, likely caused by overheating, electrical surges or improper installation. In a 2020 NREL study of about 100,000 US residential, commercial and utility-scale systems summarized by EnergySage, inverter failures were the most common cause of larger system issues.
Other equipment causes include:
- Microinverter or optimizer failures, which knock out single panels.
- Loose or damaged connectors and wiring exposed to animals such as squirrels, both of which NREL's guide flags.
- Cracked cells inside a panel. NREL's PV lifetime project describes a module that was stable for a decade before a cell crack caused a hot spot and a sudden power drop.
Our guide to a solar inverter not working walks through safe checks for the inverter itself.
Site causes: shade, dirt, snow and weather
Shade
A 2014 NREL study of 542 systems with optimizers measured an average 8.3% loss from partial shading. Trees that were small at installation can grow into the sun's path. See shading problems and fixes.
Dirt and debris
NREL's O&M guide estimates soiling from construction dust at about 5% loss and notes that nests and sprouting seeds on arrays should be removed. Rain usually cleans tilted panels.
Snow
The same guide estimates uncleared snow reduces annual output by about 3% on average and up to 15% in very snowy climates, but recommends against removal in most cases because it can damage modules and wiring.
Storms and extreme weather
NREL's 2024 study found that weather-related outages were usually short, with a median of 2 to 4 days and about a 1% median annual performance loss from 2008 to 2022. Only 12 of 6,400 systems had outages lasting two weeks or more. Long-term losses rose after hail over 1 inch, wind above 56 mph or snow deeper than 1 meter.
Heat and haze
Hot panels and smoky skies both lower output. Our guide to a summer production drop explains how much.
Is it just normal aging?
Every panel produces a little less each year. NREL's 2024 analysis of about 2,500 commercial and utility-scale sites found a median loss of 0.75% per year, with about 0.88% in hotter climates and 0.48% in cooler ones. NREL also notes 90% of systems lost less than 2% per year. Its PV lifetime project adds that early degradation can be too small to detect in the first few years.
Panel warranties set a floor. Qcells' October 2025 warranty, as an example, guarantees no more than 0.33% loss per year after year one. If a panel tests well below its warranted level, you may have a performance claim.
A simple test: if your output is down a few percent from three years ago with similar weather, that is likely aging. If it is down 15% in a year, look for a cause.
What owners should do, and what it costs
- Save monitoring screenshots showing when the drop began.
- Photograph any error codes and visible damage from the ground.
- Check breakers and the inverter status, but never open the inverter or climb on the roof.
- Find your warranty documents and installer contact information.
- Call your installer, or your leasing company if you lease. The Department of Energy notes most lease and PPA arrangements require the installer to provide system maintenance.
Costs depend on the cause. EnergySage's August 2025 guide says a service visit is around a couple of hundred dollars when labor isn't covered. Many inverter warranties cover parts but not labor, per EnergySage's September 2024 comparison. Panel warranties like Qcells' also exclude removal and reinstallation labor. Tree trimming ran less than $100 to $1,000 in EnergySage's December 2023 estimate.
If you lease or have a PPA
Leased systems and power purchase agreements work differently from owned systems. The provider usually owns the equipment and handles repairs. Read your agreement to see whether it includes any production guarantee or credits for underperformance, then report the problem in writing with dates and monitoring screenshots. That record matters if you later ask for a credit, and it helps if the provider changes hands.
Keep a simple log: the date you noticed the drop, when you reported it, who you spoke with and when the system was fixed. If a technician visits, ask for a written note of what they found.
When to call a pro
Get professional help when the system or a string is at zero after basic checks, when one panel stays far below its neighbors, when you see fault codes, burn marks or damaged wiring, or when output falls far below the same period last year without a weather explanation. If your installer has gone out of business, our solar orphans hub explains how to find a company that will service another installer's system.
Next steps
Start with the pattern table above, gather your data and make the call. To research service companies in your area, use our solar company directory.
Frequently asked questions
Why are my solar panels producing less than last year?
Common reasons include growing shade, soiling, an inverter or microinverter fault, and normal aging. Weather also varies year to year, so compare months with similar conditions.
How much should solar panel output drop each year?
Usually less than 1% a year. NREL's 2024 study of commercial and utility-scale sites found a median of 0.75% per year.
Can one bad panel reduce the whole system's output?
On a string inverter, yes, because panels are wired in series. With microinverters or optimizers, a bad panel mainly affects its own output.
Is low solar production covered by warranty?
Equipment defects and output below a panel's performance guarantee may be covered. Shade, dirt and weather are not defects, and many warranties exclude labor.
Why does my solar app show zero production?
Either the system stopped producing or the monitoring lost its connection. Check your utility meter or inverter lights to tell which one it is.
Is lower solar output in winter normal?
Yes. Shorter days, a lower sun angle and snow cover all reduce winter production, and EnergySage notes seasonal dips are not a sign of failure.
Sources
- EnergySage: What happens if your solar inverter fails? (updated Sept. 2019)
- EnergySage: When solar panel repair is needed (updated Aug. 2025)
- NREL: Best Practices for Operation and Maintenance of PV and Energy Storage Systems, 3rd Edition (Dec. 2018)
- NREL: How extreme weather and system aging affect the U.S. photovoltaic fleet (2024, updated 2025)
- NREL: Photovoltaic Lifetime Project
- NREL: Partial-Shading Assessment of Photovoltaic Installations via Module-Level Monitoring (2014 IEEE PVSC paper)
- EnergySage: NLR (formerly NREL) longevity of solar study key takeaways (updated Aug. 2021)
- EnergySage: Solar inverter warranties compared (updated Sept. 2024)
- EnergySage: What are the costs of solar after installation? (updated Dec. 2023)
- Qcells: Limited Warranty for Crystalline PV Modules, Americas (Rev04, Oct. 2025)
- DOE Energy Saver: Planning a Home Solar Electric System
Questions and comments
Be the first to ask a question or share your experience.