Solar Ownership

Solar Panel Fire Risk: How Rare It Is and How to Stay Safe

Solar Panel Fire Risk: How Rare It Is and How to Stay Safe

Rooftop solar fires are rare, and most trace back to wiring and installation mistakes. Here is what the research says and how to lower your risk.

Solar panel fire risk is low: German studies by TÜV Rheinland and Fraunhofer ISE, as summarized by inverter maker SMA, found that fewer than 0.006% of PV systems there had caused fires. When fires do happen, they most often start in the DC wiring and connectors, frequently because of installation or design mistakes, so good workmanship and periodic inspections are your best protection.

This guide explains what the data shows, which safety rules apply in the US, the warning signs to watch for and what to do if something looks wrong.

Key takeaways

  • Fires linked to solar equipment are rare, but the US Department of Energy notes plainly that "solar fires do happen."
  • TÜV Rheinland's 2018 review attributed 38% of PV fires to poor workmanship and poor design.
  • US electrical code (NEC 690.12) requires rapid shutdown so firefighters can de-energize most rooftop wiring.
  • Scorch marks, melted connectors, burning smells or repeated arc-fault errors need a professional right away.
  • Panel warranties such as Qcells' exclude damage from nearby fire, so check your homeowners insurance.

Solar panel fire risk: how common are fires?

There is no national US count of residential solar fires that we could verify. The best-known data comes from Germany, which has a large and older fleet. In an article on PV fire safety, SMA summarized research by TÜV Rheinland (Sepanski et al., 2018) and Fraunhofer ISE (Laukamp et al., 2013): fewer than 0.006% of PV systems in Germany had caused fires. TÜV's report surveyed 210 PV fires. SMA says figures reported from Japan, the Netherlands and Australia are similar.

On the US side, a DOE fact sheet on rooftop solar and firefighter safety states there was no documented case of death from electric shock, chemical burn or conventional fire caused by a solar panel. It also notes that as more buildings get solar, the chance that fires will occur on buildings with solar rises, simply because there are more of them. Put simply: the per-system risk is small, but it is not zero.

What causes solar panel fires

According to SMA's summary of TÜV Rheinland's findings, poor workmanship and poor design accounted for 38% of PV fires. The causes fall into a few groups:

Cause groupExamples from the researchHow it is prevented
Installation errorsDC connectors not fully mated, badly crimped connectors, missing strain reliefQualified installer, matched connector brands, inspection
Product failuresFaulty panels or invertersCertified equipment, warranty replacement
Planning failuresPoor mechanical or electrical design, wrong DC isolator or cablingProper design and permit review
External influencesAnimals, lightningCritter guards, wire management, surge protection

SMA also notes that most faults in Germany, Australia and the UK occurred on the DC side, the wiring between panels and the inverter. DC circuits carry steady current and can sustain an arc if a connection is loose or damaged.

Ordinary wear plays a part too. NREL's 2018 O&M best-practices guide warns that plastic wire ties and grommets break down in sunlight over time, that wiring needs protection from animals such as squirrels, and that cracked or peeling backsheets let water in and cause corrosion. It recommends re-torquing connections and thermal imaging as preventive steps.

US safety rules that lower solar fire risk

Rapid shutdown

Firefighters cannot simply flip a breaker to make rooftop panels safe, because panels produce voltage whenever light hits them. The National Electrical Code addresses this in Section 690.12. According to IAEI Magazine's summary of the code:

  • The 2014 NEC first required rapid shutdown, limiting conductors more than 10 feet from the array (or more than 5 feet inside a building) to 30 volts within 10 seconds.
  • The 2017 NEC defined the array boundary as one foot from the array in all directions and set a 30-volt limit outside it within 30 seconds.
  • From January 1, 2019, conductors inside the array boundary had to drop to no more than 80 volts within 30 seconds.
  • The 2020 NEC introduced the PV hazard control system approach, referencing UL 3741, and the 2023 edition kept the 80-volt, 30-second limit.

States adopt NEC editions on different schedules, so an older system may have been installed under earlier rules. Some equipment is listed for this purpose; Enphase, for example, says its IQ8 microinverters are UL Listed as PV rapid shutdown equipment when installed per its instructions.

Fire ratings and setbacks

Panels carry a fire classification. Qcells' Q.PEAK DUO BLK ML-G10.C+ data sheet, for example, lists a Type 2 fire rating under ANSI/UL 61730. Local fire codes may also require roof pathways and setbacks so crews can work on the roof. See our guide to fire codes and solar setbacks.

Arc-fault and ground-fault detection

Modern inverters watch for arcing and insulation faults and shut down when they find one. SolarEdge's North American HD-Wave guide, for example, says the inverter has an isolation monitor interrupter for ground-fault protection. If you see these errors, don't keep resetting the system. Our explainer on ground-fault and arc-fault errors covers what they mean.

Warning signs of solar panel fire risk and what to do

You can check for most warning signs from the ground or through your monitoring app:

  • Burn marks, brown spots or melted plastic on panels, connectors or the inverter.
  • A burning-plastic or hot-electrical smell near the inverter or main panel.
  • Repeated arc-fault or ground-fault errors.
  • Loose, sagging or chewed wires under the array.
  • Scorched or discolored areas on the inverter casing.
  • Production that drops suddenly on one string or panel.

If you smell burning or see smoke, get everyone out and call 911. Tell the dispatcher the home has solar panels, and a battery if you have one. Do not spray water on the inverter or climb onto the roof.

For non-emergency signs, turn the system off using the procedure in your owner's manual, usually the AC disconnect and the rapid shutdown switch, and call a qualified installer. Do not open the inverter or handle panel connectors yourself.

Batteries and fire safety

Home batteries add a separate set of considerations. In slides from a June 2025 Clean Energy Group presentation on fire safety, a retired Las Vegas Fire & Rescue captain advised responders to isolate grid, solar and battery power, ventilate enclosed spaces, use copious water to cool lithium-ion cells and have a qualified electrician remove damaged batteries because they can rekindle. For homeowners, the practical takeaways are to install batteries where the manufacturer and local code allow, keep the area clear of clutter, and label shutoffs clearly.

Costs, warranties and insurance

Inspections and repairs are modest compared with the risk they reduce. EnergySage's August 2025 repair guide says a service visit runs around a couple of hundred dollars when warranty does not cover labor.

Warranties are narrower than many owners expect:

  • Qcells' October 2025 module warranty for the Americas excludes environmental damage including nearby fire, plus acts of nature such as hail and storms, and work that does not follow the installation manual.
  • EnergySage's 2024 warranty comparison says most inverter makers will not cover damage from extreme weather events, which homeowners insurance typically handles.
  • Your installer's workmanship warranty may cover faults caused by their installation, such as bad connectors. See what a workmanship warranty covers.

Call your insurer to confirm your policy lists the solar system and covers fire damage to it.

When to call a pro

Book an inspection if your system is several years old and has never been checked, after a storm or animal activity, or anytime you see the warning signs above. Ask the technician to check connectors, wire management, grounding and the inverter area, and to use thermal imaging if available. If your installer has gone out of business, our solar orphans hub explains how to find a new service company.

Next steps

Walk around your home and look at what you can see from the ground, check your app for fault messages and confirm you know where your shutoffs are. If you need a technician, start with the solar company directory to research local installers' track records.

Frequently asked questions

Can solar panels catch fire on their own?

It is rare. Research summarized by SMA found that fewer than 0.006% of PV systems in Germany caused fires, and most traced back to wiring, connectors or design errors rather than the panels themselves.

Do solar panels increase the risk of a house fire?

Any electrical system adds some risk. A properly designed and installed system that meets current code, with periodic inspections, keeps that added risk low.

What is solar rapid shutdown?

It is a code requirement in NEC 690.12 that lets the voltage in rooftop solar wiring be reduced quickly, so firefighters can work more safely. Newer rules apply limits both inside and outside the array boundary.

Does homeowners insurance cover solar panel fire damage?

Many policies cover rooftop solar as part of the home, but terms vary. Call your insurer to confirm the system is listed and what deductible applies.

What should I do if I smell burning near my inverter?

Leave the house and call 911 if you see smoke or flames, and tell the dispatcher you have solar. If there is only a smell, shut the system off as your manual describes and call a qualified installer.

Sources

Related guides

Questions and comments

Be the first to ask a question or share your experience.

Comments are checked before they appear. No links or advertising. Guidelines.

Calculators for this topic

More solar ownership guides

All solar ownership guides →