How to Tell If Solar Panels Are Working: 5 Checks Any Homeowner Can Do
Five quick checks, from your monitoring app to your utility meter, that show whether your solar system is producing, plus the warning signs that mean it is not.
The quickest way to tell if solar panels are working is to open your monitoring app around midday on a sunny day and confirm it shows power being produced, then glance at the inverter for a green status light. You can double-check with your utility meter, which on many net meters shows a separate reading for electricity your home sends back to the grid.
None of these checks requires climbing on the roof or opening equipment. Here are five you can do in a few minutes, and what the results mean.
Key takeaways
- A healthy system's daily production graph rises in the morning, peaks around noon and falls toward sunset. Tesla describes it as a wave.
- On many inverters, a steady green light means the system is producing and red means an error.
- Net meters show exported energy. Dominion Energy, for example, uses register 35 for energy received by the grid from your solar.
- Your bill is a slower but useful check. A sudden jump in grid use with no change in habits can signal a solar outage.
- Monthly output can vary a lot with weather, so compare with the same month last year, not with last month.
Check 1: Look at your solar monitoring app
Most systems come with an app from the inverter maker or installer. On a clear day, the production graph should look like a hill, rising from early morning, peaking near noon and falling toward sunset. Tesla's support page describes this shape as a wave.
What to look for:
- A flat line at zero in daylight: the system is not producing.
- A normal curve that suddenly stops: something tripped or failed at that time.
- A "last reported" date days ago: the app has lost contact, which does not always mean the panels stopped.
- One panel at zero in a panel-level app: a single-panel or microinverter fault.
If your app has gone quiet, see solar monitoring stopped working: what to do. Enphase, for example, says in its US warranty that products should stay continuously connected to the internet so problems can be diagnosed remotely and firmware kept current.
Check 2: Read the inverter's status light
Walk to your inverter, usually on a wall near the meter or in the garage, around midday. On SolarEdge's earlier North American inverters, its user manual says a steady green light means producing power, blinking green means standby, and a red light means an error. Enphase microinverters use flashing green for normal operation, flashing orange for a lost connection to the IQ Gateway, and red for a grid problem or DC fault, though those lights sit under the panels and are hard to see.
No light at night is normal. No green light at noon on a sunny day is not. Our guide on how to read your solar inverter display covers screen readings and codes in detail.
Check 3: Watch your utility meter
Your utility meter gives an independent check that does not depend on Wi-Fi. Meters vary by utility, but two examples show the idea:
- Dominion Energy (Virginia): on its bidirectional net meter, register 04 shows electricity delivered from the grid, and register 35 shows excess solar electricity received by the grid. A separate one-way generation meter, if you have one, uses register 01 for total solar production.
- San Diego Gas & Electric: its smart meters label delivered energy "DEL" and received energy "REC." SDG&E notes the meter shows only what flows back to the grid, not your total solar output.
To test, write down the received (export) reading in the morning and again in the late afternoon on a sunny day. If it climbs, your system is producing more than your home is using. If it never moves on sunny days for a week, investigate further. Your utility's website explains its own meter codes.
Check 4: Compare your electric bills
Bills are slower but hard to argue with. Put this year's bill next to the same month last year. If your household use is about the same but the energy you bought from the grid jumped, or your export credits fell sharply, the system may have been down for part of the month.
Keep weather in mind. The PVWatts Version 5 manual from NREL (now the National Laboratory of the Rockies) says a specific month's output can differ from the long-term average by up to about 40%. One bad month is not proof of a fault. Two or three in a row, against a normal year, is worth a call.
Check 5: Look at the panels from the ground
From your yard, scan the array. You are looking for obvious problems, not doing an inspection:
- Cracked or shattered glass.
- Heavy shade from trees that have grown since installation. Tesla lists tree growth among the causes of lower output.
- Thick dirt, pollen, bird droppings or snow cover.
- Loose or hanging wires, or nests under the panels.
In winter, a blanket of snow can stop production for a while. The Department of Energy's winter resilience guidance says to remove snow only when there is substantial accumulation, and then gently with a broom rather than a shovel. Our article on snow on solar panels covers when it is worth it.
Do not climb up. Tesla's owner guidance says not to walk on panels and not to attempt repairs yourself.
What your checks are telling you
| What you see | Likely meaning | What to do |
|---|---|---|
| App shows normal midday curve, green inverter light | Working normally | Nothing |
| App offline but inverter light green and meter export climbing | Monitoring problem, production probably fine | Reconnect Wi-Fi or contact installer about monitoring |
| Zero production on a sunny day, no green light | System off or faulted | Check solar breaker and inverter switch, then call for service |
| Red light or error code | Fault detected | Note the code and call your installer |
| One panel at zero, others normal | Single panel, optimizer or microinverter issue | Report it for a warranty check |
| Lower output every month for a year | Shade, soiling, degradation or a partial fault | Compare with your estimate and ask for an inspection |
If you have microinverters and one unit reports nothing, read microinverter failure: what to do.
When to call a professional, and what it may cost
Call your installer or a solar technician when a red light or error persists, production is zero on sunny days after you have checked the solar breaker, output has been well below normal for months, or you see physical damage. Do not open the inverter or touch wiring.
Angi's solar maintenance cost guide (checked November 2026) lists solar inspections at about $150 to $300. Before paying, check who is responsible. DOE's Energy Saver says most lease and power purchase agreements require the installer to provide maintenance, while owners of purchased systems usually handle upkeep themselves. Your installer's workmanship warranty and the equipment warranties may cover the repair, even if not the visit. If the installer has closed, start with our solar orphans guide.
How often to run these checks
A quick look at the app once a week, or turning on its alert notifications, catches most outages within days. Do the meter and bill comparison monthly, and a full production review once a year. The sooner you notice a problem, the less production you lose while waiting for a repair.
Next steps
Make the app check a monthly habit and save a screenshot of a normal sunny day as your baseline. Once a year, total your production and compare actual vs estimated solar production to catch slow problems that daily checks miss.
Frequently asked questions
How do I know if my solar panels are producing electricity?
Check your monitoring app at midday on a sunny day for a rising production curve and look for a green light on the inverter. Your utility meter's export reading is a backup check.
Can my solar panels stop working without me noticing?
Yes. If monitoring is offline or you do not check it, an outage may only show up on your bill. A monthly app check catches most problems early.
Why does my meter not show my total solar production?
A net meter records only the electricity sent back to the grid after your home uses what it needs. SDG&E notes this on its net metering page. A generation meter or the inverter shows total output.
How much does a solar panel inspection cost?
Angi's cost guide, checked in November 2026, lists solar inspections at about $150 to $300. Prices vary by location and system size.
Is it normal for solar output to drop in winter?
Yes. Tesla says winter noon output is typically closer to 50% of a system's potential, versus up to 100% in summer, because days are shorter and the sun is lower.
Sources
- Tesla Support – Understanding System Performance
- SolarEdge Single and Three Phase Inverter User Manual, North America
- Enphase IQ8 Installation and Operation Manual – Status LED indications (Jan. 2024)
- Dominion Energy – Understand My Meter
- SDG&E – Smart Meters and Net Metering
- NREL – PVWatts Version 5 Manual (2014, archived copy)
- Angi – Solar Panel Maintenance Cost
- DOE Energy Saver – Planning a Home Solar Electric System
- Enphase IQ8 Microinverter Limited Warranty (USA-Canada)
- Tesla Support – Solar Panel Maintenance
- DOE – Solar Photovoltaic Hardening for Resilience: Winter Weather
Questions and comments
Be the first to ask a question or share your experience.