Snow on Solar Panels: Should You Remove It or Let It Slide?
Most of the time, the best thing to do about snow on your panels is wait. Here is when clearing makes sense, how to do it without damage, and what to inspect after.
For most homeowners, snow on solar panels is best left to slide off on its own. The Department of Energy (DOE) advises removing snow only when there is a substantial buildup, and then gently with a broom rather than a shovel, while panel makers such as Tesla say never to shovel panels or use hard-edged tools.
Snow does stop production while it covers the glass, but the loss is usually temporary, and clearing a roof in winter carries real risks to you and your equipment. Here is how to decide.
Key takeaways
- Snow usually slides off tilted panels as they warm. Tesla notes that the tempered glass on its panels is very good at shedding snow on its own.
- Annual snow losses vary widely by location. A 2017 NREL (now NLR) modeling study found losses from 0% to about 16% for fixed systems in the continental US, highest in Minnesota and Michigan.
- If you clear snow, use only a soft broom or similar tool from the ground. Qcells says to remove snow and ice carefully, without force.
- Clear snow from below the array so snow sliding off the panels has somewhere to go, as DOE recommends.
- Have a professional inspect the system after a heavy snow season or an extreme storm.
Does snow on solar panels hurt production?
Yes, while it covers them. Tesla's support pages say a larger buildup of snow may prevent a system from producing power until the panels are clear. Its owner manual adds that snow that temporarily reduces production is "not a cause for concern."
Over a full year, the impact depends on where you live and how your panels are tilted. NREL's 2017 report on a snow model for its System Advisor Model software found:
- Fixed-tilt systems in the continental US lost from 0% to about 16% of annual energy to snow, with the highest losses in Minnesota and Michigan.
- Panels tilted at an angle equal to the site's latitude generally lost less than panels tilted at 20 degrees across the continental US.
- Local differences can be large. Flagstaff, Arizona, was modeled at 3.0% to 4.7%, while Phoenix showed 0%.
Snow losses happen in winter, when short days already cut output. Tesla says a system's winter noon output is typically closer to 50% of its potential, versus up to 100% in summer.
Should you remove snow from solar panels?
Usually not. Here is a quick way to decide.
| Situation | Our suggestion | Why |
|---|---|---|
| Light dusting, sunny days ahead | Leave it | It typically melts or slides off quickly |
| Heavy snow, panels easy to reach from the ground | Optional: gently brush the lower edge with a soft tool | DOE says remove snow only if accumulation is substantial, using a broom not a shovel |
| Snow piled below the array, blocking sliding | Clear the area below if safe | DOE recommends clearing snow from the ground or roof around the system so it can shed |
| Panels reachable only by climbing the roof | Leave it or hire a pro | Winter roofs are dangerous, and manufacturers say not to walk on panels |
| Ice dams, heavy drifts or sagging panels | Call a professional | Uneven loads can exceed what the system is designed for |
If you only gain a day or two of production by clearing snow, the electricity is rarely worth a fall risk or a scratched panel.
How to remove snow from solar panels safely
If you decide to clear snow, follow the panel makers' rules:
- Stay on the ground. Use a soft broom or a snow tool designed for panels on an extension pole. Do not climb onto a snowy or icy roof.
- Use no force. Qcells' North American manual says to remove snow and ice carefully, without force, for example with a very soft broom.
- Never shovel or scrape. Tesla says never to shovel or use a hard-edged tool, and DOE also says to use a broom, not a shovel.
- Leave the ice. Chipping ice can crack glass. Let the sun do the work.
- Skip the hot water. Qcells warns against cleaning with water when there is a risk of frost.
- Clear the landing zone. Make sure snow sliding off the panels will not land on people, walkways, vents or meters.
If you are not sure whether clearing is safe, wait it out. NREL's snow model treats sliding as the main way snow leaves tilted panels, and Tesla notes its panel glass is very good at shedding snow on its own.
Snow load: when snow becomes a damage risk
Panels are rated for weight. Qcells' datasheet for its Q.TRON BLK M-G2+ panels lists a design load of 5,400 pascals (113 pounds per square foot) pushing down, with a higher test load of 8,100 pascals. Those ratings assume the panel is mounted as the manual specifies.
Problems arise with uneven loads. Qcells' manual warns about unbalanced loads such as snow overhangs and drifts that significantly increase local loads, and REC's manual says that in areas of snow build-up, panels can face forces beyond the stated limit, recommending extra support, especially on the lower row. DOE's winter guidance adds that accumulated snow may warp or even break a panel, and that ice can shift the system's weight in ways that overstress frames and supports.
Warning signs after a big storm:
- Panels that look bowed, tilted or out of line with their neighbors.
- Cracked glass or frames that look bent or separated.
- Ice dams forming along the roof edge below the array.
- Production that stays low after the snow has clearly melted.
After winter: inspections and warranty points
DOE recommends having a trained professional inspect the system after each winter season or extreme weather event, looking for broken glass, detached frames and warped panels. Qcells' manual likewise calls for inspections after events such as high snow loads.
Snow damage and warranties do not always mix well. Panel warranties usually cover manufacturing defects, not weather or handling damage. Enphase's US microinverter warranty, for example, excludes acts of nature, and Qcells says damage from cleaning methods and tools is not covered by its product and performance warranty. If a storm damages your array, check your homeowners insurance as well as your equipment warranties. Our guide on filing a solar panel warranty claim walks through the evidence to gather.
Who pays for snow-related service?
If you lease your panels or buy power under a power purchase agreement, call the company before you hire anyone. DOE's Energy Saver guidance says most lease and PPA arrangements require the installer to provide system maintenance, while owners of purchased systems are generally responsible for upkeep themselves. Ask whether post-storm inspections are included, and whether your contract restricts who may touch the panels. Owners who bought their systems should get a written quote for any inspection or snow clearing, and confirm the contractor carries insurance for roof work.
Snow also explains many "low production" scares. When you compare actual vs estimated solar production, remember that PVWatts assumes 0% snow loss by default, so an estimate made with default settings may run high in snowy areas.
Next steps
Before the next storm, locate a soft, panel-safe snow tool and plan where sliding snow will land. For more on living with solar in cold places, read solar panels in snowy climates. If storm damage needs repair and your installer is no longer in business, our solar orphans guide explains where to turn.
Frequently asked questions
Do solar panels work with snow on them?
Not well while they are covered, because snow blocks sunlight. Tesla says a larger buildup may stop production until the panels are clear, but snow on tilted panels usually slides off on its own.
Is it OK to use a roof rake on solar panels?
Only a soft tool made for panels, used gently from the ground. Tesla says never to shovel or use a hard-edged tool, and Qcells says to remove snow without force, for example with a very soft broom.
Can snow damage solar panels?
Heavy or uneven snow can. DOE says accumulated snow may warp or break panels, and Qcells and REC warn that drifts and overhangs can exceed load ratings.
How much production do solar panels lose to snow each year?
It depends on location and tilt. NREL modeling found annual losses for fixed systems in the continental US ranging from 0% to about 16%, highest in Minnesota and Michigan.
Should I pour warm water on snowy solar panels?
No. Qcells advises against cleaning modules with water when there is a risk of frost. Let the sun melt the snow.
Sources
- DOE – Solar Photovoltaic Hardening for Resilience: Winter Weather
- NREL – Integration, Validation, and Application of a PV Snow Coverage Model in SAM (2017)
- Tesla Support – Solar Panel Maintenance
- Tesla Solar Owner Manual – System Performance and Maintenance
- Tesla Support – Understanding System Performance
- Qcells Q.TRON M-G2.X Series Installation and Operation Manual (North America)
- Qcells Q.TRON BLK M-G2+ datasheet
- REC Alpha Series Installation Manual (UL)
- NREL – PVWatts Version 5 Manual (2014, archived copy)
- DOE Energy Saver – Planning a Home Solar Electric System
- Enphase IQ8 Microinverter Limited Warranty (USA-Canada)
Questions and comments
Be the first to ask a question or share your experience.