Solar Ownership

Solar Production Drop in Summer: Causes and What to Do

Solar Production Drop in Summer: Causes and What to Do

Panels make less power when they're hot, and summer adds smoke, pollen and leafy shade. Here is how to tell normal dips from real problems.

A solar production drop in summer is usually caused by heat, because panels convert sunlight less efficiently as they get hotter, along with haze or wildfire smoke, dust and pollen, and new leaf growth on nearby trees. Long summer days often still produce plenty of energy, so if output falls well below the same month last year in similar weather, or one part of the system stops completely, it is time to look for an equipment problem.

Here is how to sort normal summer behavior from issues that need a fix.

Key takeaways

  • Heat reduces panel output. A typical data sheet lists a temperature coefficient around -0.34% per degree Celsius above 25°C cell temperature.
  • Wildfire smoke can sharply cut output; EIA reported California grid solar output fell nearly 30% from its July 2020 average during September 2020 fires.
  • Summer brings dust, pollen and leaves that act as shade.
  • Inverters can overheat too, especially if mounted in direct sun.
  • Compare against the same month last year, not against spring.

Why a solar production drop happens in summer heat

Solar cells produce slightly less power as they warm up. Manufacturers publish this as a temperature coefficient. Qcells' Q.PEAK DUO BLK ML-G10.C+ data sheet, for example, lists -0.34% per degree Celsius for maximum power. Panel ratings are measured at a 25°C cell temperature under standard test conditions.

On a hot, sunny roof, cells run far warmer than the air. The same data sheet gives a nominal module operating temperature of about 43°C (109°F) under moderate sun. Using its coefficient, here is an illustration of the rough effect at the same light level (simple multiplication, not a measurement):

Cell temperatureDegrees above 25°CIllustrative power change (at -0.34%/°C)
25°C (77°F)00% (rated conditions)
43°C (109°F)18About -6.1%
50°C (122°F)25About -8.5%
65°C (149°F)40About -13.6%

Your panels' coefficient may differ, so check your own data sheet. Longer days usually offset some of this, which is why summer totals are often still high even as peak midday power dips.

Heat also matters over the long run. NREL's 2024 fleet study found that systems in hotter climates lost about 0.88% of performance per year, nearly twice the 0.48% seen in cooler climates. That study covered about 2,500 commercial and utility-scale sites, not home systems.

Other common causes of a summer solar production drop

Smoke and haze

Fine particles in smoke block sunlight before it reaches the panels. The US Energy Information Administration reported that during the first two weeks of September 2020, solar generation on California's main grid fell nearly 30% from the July 2020 average as wildfires burned. That was grid-scale data, but rooftop panels under the same smoky skies face the same loss of sunlight. Our guide to solar panels and wildfire smoke covers what to expect.

Dust, pollen and droppings

Dry summers mean less rain to rinse panels. NREL's 2018 O&M guide estimates soiling from sources like construction dust at about 5% loss. NREL's PVWatts model has used a default soiling loss of 2% as a general assumption, which gives a sense of how much varies by site.

Leafy trees

Deciduous trees fill in during late spring and summer, and they may have grown since last year. A new afternoon notch in your power curve often traces back to a branch. See our guide to shading fixes.

An overheating inverter

EnergySage's August 2025 repair guide names overheating as a likely cause of inverter problems. In summarizing a 2020 NREL field study of about 100,000 systems, EnergySage linked many inverter problems to poor installation and noted that inverters need to be shaded for maximum longevity. NREL's O&M guide also notes that inverter air filters collect dust and grass and should be cleaned after dusty periods.

Grid voltage trips

Grid-tied inverters disconnect when utility voltage or frequency goes outside set limits under the IEEE 1547 standard; SolarEdge's North American installation guide notes that changing those set points requires utility approval. If your app shows repeated grid errors on sunny afternoons, ask your installer to review the logs and raise it with your utility.

How to check whether a summer solar production drop is normal

  1. Compare like with like. Use this July versus last July, not July versus April. Weather-adjusted comparisons, which some apps offer, are even better.
  2. Check an estimate. The free PVWatts calculator from the National Laboratory of the Rockies (formerly NREL) at pvwatts.nlr.gov gives typical monthly production for your location and system. Your installer's proposal may include a monthly estimate too.
  3. Look at the daily curve. Smooth but lower suggests heat or haze. Notches suggest shade. A flat line at zero means something is off.
  4. Check panel-level data if you have microinverters or optimizers. Uniform dips point to weather; one weak panel points to equipment.
  5. Read the inverter. Note any error codes or a red light.

Lower production or higher use? Check your bill too

Many owners first notice a "drop" when a summer electric bill jumps. That is not always the panels. Air conditioning, pool pumps and fans can push household use far above what the system makes, so you import more from the grid even when production is normal.

To separate the two, put your app's monthly production next to your bill's import and export figures for the same period. If production is close to last summer but imports rose, the change is on the demand side. Our article on the average summer electric bill explains what typically drives those costs, and trimming cooling loads may help more than anything you do on the roof.

What you can do about it

  • Accept normal heat loss. There is no safe homeowner fix for cell temperature. Do not spray panels with water to cool them; Qcells' manual says to clean only modules that have cooled down.
  • Clean if soiling is heavy. Rain usually handles it. If not, follow the manufacturer's instructions, avoid abrasives and stay off the roof. EnergySage estimated professional cleaning at often less than $10 per panel (December 2023). See how to clean solar panels safely.
  • Trim trees. EnergySage put trimming or removal at less than $100 up to $1,000 depending on size (December 2023).
  • Keep the inverter area clear. Don't stack boxes or store items against it, and keep vents unblocked.
  • Wait out smoke. Output returns when the air clears, though ash can leave a film worth checking afterward.

Warranty and cost considerations

Normal heat loss and weather are not defects, so they are not warranty issues. Performance warranties guarantee a minimum output measured under standard conditions, not your summer production. Qcells' 2025 warranty, for example, excludes acts of nature and environmental factors such as blowing sand and nearby fire.

An inverter that fails from heat may be covered if it was installed correctly. EnergySage's 2024 comparison shows many inverter warranties cover parts but not labor. Its August 2025 guide says to expect around a couple of hundred dollars for a service visit when labor is not covered. If an installation flaw like a sun-baked inverter location caused the issue, your installer's workmanship warranty may apply.

When to call a pro

Call your installer or a certified technician if production is well below the same month last year in similar weather, if any panel or the whole system reads zero on a sunny day, if the inverter shows a fault, or if you see burn marks or melted connectors. If your installer is no longer in business, our solar orphans hub explains where to turn.

Next steps

Pull up last summer's numbers, compare them with this month and look at a clear day's power curve. If something does not add up, work through our guide to why a solar system produces less power.

Frequently asked questions

Do solar panels produce less in hot weather?

Yes. Panels lose a small percentage of output for each degree they run above 25 degrees Celsius; one common data sheet lists 0.34% per degree.

Why is my solar production lower in July than in May?

Hotter panels, more haze and leafy trees can all lower midday output in July even though days are long. Compare with last July instead of with spring.

Should I spray water on my solar panels to cool them?

No. Manufacturers such as Qcells say to clean only panels that have cooled down, and spraying hot panels or climbing on the roof adds risk without a meaningful benefit.

Does wildfire smoke affect solar panels?

Yes. Smoke particles block sunlight; EIA reported California grid solar output fell nearly 30% from the July average during September 2020 fires.

When is a summer drop a sign of a problem?

When output is far below the same month last year in similar weather, when one panel or the whole system shows zero, or when the inverter displays an error.

Sources

Related guides

Questions and comments

Be the first to ask a question or share your experience.

Comments are checked before they appear. No links or advertising. Guidelines.

Calculators for this topic

More solar ownership guides

All solar ownership guides →