Solar

Does Solar Cost More on a Steep or Complex Roof?

Does Solar Cost More on a Steep or Complex Roof?

Steep, tile or chopped-up roofs often raise solar labor and design costs. Here is what drives the extra cost, what the data says, and how to judge a quote.

Yes, solar usually costs more on a steep or complex roof, because it takes more labor, more safety gear and more design work to install. EnergySage rates tile roofs as the most labor-intensive common roof for solar, and roof issues are one of the main reasons quotes rise after a site visit. There is no published national surcharge for a complex roof, so the best approach is to ask each installer to itemize any roof-related costs.

Key takeaways

  • Tile roofs often need tiles removed and replaced around each mount, which adds labor.
  • Standing-seam metal roofs can lower labor because mounts clamp to the seams without drilling.
  • Steep roofs require fall protection for crews under federal OSHA rules, which adds setup time.
  • Many small roof faces can mean more design work, more wiring and fewer panels per face.
  • Installer and state usually move price per watt more than roof type, so compare several quotes.

Why a complex roof raises solar cost

Labor and design are a meaningful part of every solar price. EnergySage, citing a 2021 NLR (formerly NREL) study, puts installation labor at about 7% of a typical system's price, electrical wiring at 9% and racking at 3%. A roof that slows the crew or needs extra parts pushes those lines up.

EnergySage's article on cost changes after a site visit (last updated in 2020) lists the main culprits. Final roof measurements can change the design, which "could either increase or decrease installation costs." Examples include extra equipment, longer cabling or a more complex installation. Roof repairs or reinforcement before adding panels can also be added at that stage.

Solar cost on a complex roof by roof type

EnergySage's roof material guide (updated October 2022) rates solar labor cost by roof type on a relative scale, where more dollar signs mean higher cost.

Roof typeRelative solar labor costWhy
Asphalt shingle$$Installers drill into the roof, then seal and flash each attachment
Metal (standing seam)$Mounts can clamp to raised seams with no drilling
Tar and gravel (flat)$$$Needs tilted racking to angle panels toward the sun
Tile$$$$Brittle tiles are often removed and replaced with a mounting foot and flashing

EnergySage notes that not all installers have the skills for tile work. On metal roofs, the method depends on the type: standing-seam roofs use clamps on the raised seams, while corrugated metal needs holes drilled. EnergySage's guide says wood shake is not suitable for solar and should be replaced with a compatible material first.

Does a steep roof cost more for solar?

Steep roofs are harder and slower to work on. Under federal OSHA construction rules (29 CFR 1926.501), each worker on a steep roof with unprotected sides and edges 6 feet or more above a lower level must be protected by guardrails with toeboards, safety nets or personal fall arrest systems. Setting up that protection and moving carefully takes time, and time is labor cost.

We could not find a published national figure for how much a steep pitch adds. An installer may list it as a separate line or fold it into the price per watt, so ask directly. A fair quote should explain why any steep-roof charge is needed.

A steep pitch is not all bad. EnergySage says the best panel angle is about 30 degrees and is usually close to your latitude. So a steeper south-facing roof can sit close to the ideal angle for production.

Many roof faces, dormers and obstructions

A roof with several small faces, valleys, dormers, vents and skylights is "complex" even if it is not steep. Common effects include:

  • Fewer panels per face. EnergySage notes installers need space around edges, vents and chimneys, which leaves less room on small faces.
  • More design work. Each roof face may need its own layout.
  • More wiring. Longer cable runs between faces add material and labor.
  • Different production. East- or west-facing panels produce less than south-facing ones in the Northern Hemisphere, so the same panels may make fewer kWh.

Berkeley Lab reports a median roof-coverage ratio of 31% for multi-story homes and 22% for single-story homes in its 2026 data update. Even with good planning, a large share of most roofs is not used for panels.

Roof condition can matter more than roof shape

The biggest roof-related cost is often a roof that needs replacing. EnergySage's roof replacement guide (updated May 2026) says that if your asphalt roof is over 10 years old, you should probably replace it before going solar. It puts later removal and reinstallation of panels at $1,500 to $6,000. Its 2022 roof material guide put an average roof replacement at about $8,000 at that time, depending on material, location, size and complexity.

Ask your installer to inspect the roof and tell you in writing whether it should be repaired or replaced first.

What the site visit checks on a complex roof

Most first quotes are based on satellite images. The final price is set after someone visits. EnergySage lists the changes that most often come up at that stage:

  • Roof repairs or reinforcement. Signs of aging or structural problems may need fixing before the roof takes the extra weight of panels.
  • Tree trimming or removal. Trees may have grown since the satellite image was taken.
  • Design changes. Real measurements and the best spots for the inverter and cables can change the layout.
  • Electrical panel upgrade. EnergySage's 2020 article put this at typically $1,000 to $3,000 when the existing panel is too old or too small; check current local prices.

EnergySage advises that if an installer cannot explain a price increase, you should treat it as a red flag. On a complex roof, ask for photos and a revised layout that shows where each panel goes.

Questions worth asking before you sign:

  • How many roof faces will be used, and how many panels on each?
  • What is the expected yearly kWh for each face?
  • Has your crew installed on this roof material before?
  • Who fixes a leak or a broken tile later, and for how long?

Is ground-mounted solar an alternative?

If your roof is too complex, shaded or fragile, a ground mount may be an option if you have the yard space. It is not cheaper, though. Berkeley Lab's 2024 Tracking the Sun summary found ground-mounting raised residential prices by about $0.40 per watt in 2023 data, and its 2026 update notes ground mounts are rarely used for homes. See our guide to ground-mounted vs. roof-mounted solar.

How to judge a complex-roof quote

Price differences between installers are large anyway. Berkeley Lab found 2025 median prices among the top 100 residential installers ranged from about $2.4 to $6.3 per watt. So a complex roof does not mean you should accept any price.

  1. Get at least three quotes, ideally from installers experienced with your roof type.
  2. Ask each one to itemize roof-related charges, such as tile work, steep-roof fees or reinforcement.
  3. Compare price per watt with and without those extras.
  4. Check the roof-penetration and workmanship warranty. EnergySage says installer roof warranties are typically 10 years.
  5. Ask how tiles will be handled and whether spares are included.

One more check: the IRS says the Section 25D credit is not allowed for expenditures made after December 31, 2025, and a solar expenditure counts as made when installation is complete. A 2026 quote for a system you will own should not subtract a federal credit.

Next steps

Check whether your home suits solar with our guide is my house good for solar, estimate output with the solar panel calculator, and run each bid through the solar quote checker to see if the roof extras push the price out of line.

Frequently asked questions

Does a steep roof make solar more expensive?

Often, yes. Crews need fall protection and work more slowly on steep roofs, which adds labor. There is no standard surcharge, so ask installers to itemize it.

Is solar more expensive on a tile roof?

Usually. EnergySage rates tile as the most labor-intensive common roof for solar because the tiles are brittle and are often removed and replaced around each mount.

What is the cheapest roof type for solar?

EnergySage rates metal roofs, such as standing seam, as having the lowest solar labor cost, since mounts can clamp to the seams without drilling. Asphalt shingle is also common and straightforward.

Can solar go on a roof with many angles?

Yes, but small roof faces hold fewer panels and may need more wiring and design work. East- and west-facing panels also produce less than south-facing ones.

Should I replace my roof before installing solar?

EnergySage suggests replacing an asphalt roof that is over 10 years old before going solar, because removing and reinstalling panels later can cost $1,500 to $6,000.

Sources

Related guides

Questions and comments

Be the first to ask a question or share your experience.

Comments are checked before they appear. No links or advertising. Guidelines.

Calculators for this topic

More solar guides

All solar guides →