Solar for a Shed: What a Small System Can Run, How to Size It and Code Basics
A small solar setup can light a shed and charge tools without trenching a cable. Here is how to size it, which setup fits your use and the code basics to know.
Solar for a shed is usually a small stand-alone setup: one or a few panels, a charge controller, a battery and an inverter, either as separate parts or built into a portable power station. It is a good fit for lights, a fan, phone and tool-battery chargers and occasional short tool use, and it avoids digging a trench for a cable from the house. It is a poor fit for heavy, long-running loads like space heaters, air conditioners or a workshop full of big stationary tools, which need much larger systems or a proper electrical feed.
Key takeaways
- Most sheds need only a few hundred watt-hours a day, which a small system can supply.
- Tools with motors draw a surge when they start, so check the inverter's surge rating as well as its continuous rating.
- A portable power station plus one panel is the simplest setup; a component system is cheaper to expand.
- Electrical code still applies to stand-alone systems, and batteries need protection from heat and cold.
- Never run a fuel generator inside a shed.
What solar for a shed can and cannot run
Whether a load works depends on two limits: the inverter's continuous and surge watts (how big a load can start and run) and the battery's watt-hours (how long). For example, EcoFlow lists its DELTA 3 Plus power station at 1,024 Wh of capacity with 1,800 W continuous and 3,600 W surge output.
| Load type | Examples | Fit for a small shed system? |
|---|---|---|
| Low, steady loads | LED lights, a small fan, a radio, a Wi-Fi camera | Yes, easily |
| Charging | Cordless tool batteries, phones, a laptop | Yes |
| Short motor loads | Drill, jigsaw, small shop vacuum, used briefly | Usually, if within the inverter's continuous and surge ratings |
| Heavy motor loads | Table saw, air compressor, large welder | Often not; check surge and run time carefully |
| Heating and cooling | Space heater, window AC, electric water heater | Generally not practical |
Look up typical wattage for common appliances on our cost to run pages, such as the space heater page, to see why heating is usually ruled out.
Sizing math for shed solar
DOE's Energy Saver formula is wattage times hours per day, divided by 1,000, for daily kWh. If a tool label shows only amps, multiply amps by volts; most U.S. tools run at 120 V. Our kWh calculator and watts to amps calculator handle the conversions.
A sample hobby shed, using round numbers for illustration:
- LED shop lights: 40 W for 3 hours = 120 Wh
- Small fan: 30 W for 3 hours = 90 Wh
- Charging two cordless tool batteries: say 100 Wh
- Radio and phone: about 30 Wh
- Total: about 340 Wh per day
Battery
To ride through two cloudy days, you need 340 x 2 = 680 Wh of usable storage. Victron's sizing guide says lithium batteries can typically be discharged to about 90 percent and lead-acid to about 50 percent, so plan on roughly 760 Wh of lithium or 1,360 Wh of lead-acid. A 1 kWh lithium power station or a single 100 Ah, 12 V lithium battery (about 1,200 Wh) covers this shed.
Panels
At 4 peak sun hours, 340 / 4 = 85 W keeps pace on a clear day. Adding margin for losses, shade and short winter days, 150 to 200 W of panels is a reasonable target. Check your site's sun hours with PVWatts from the National Laboratory of the Rockies (pvwatts.nlr.gov), and remember that trees shading a backyard shed can cut output far more than any spec sheet suggests.
Controller
For a component system, match the controller to the panels. Victron's SmartSolar MPPT 100/30, for instance, is rated for 440 W of panels at 12 V and accepts up to 100 V open-circuit from the array, which is plenty for a 200 W shed setup.
Three ways to set up shed solar
| Setup | Example parts and November 2026 list prices | Pros | Cons |
|---|---|---|---|
| Power station plus panel | EcoFlow DELTA 3 Plus ($719, pre-order) with a panel matched to its 11 to 60 V solar inputs | No wiring, built-in outlets, portable | Higher cost per Wh of storage; outlets only on the unit |
| 12 V component system | Battle Born 100 Ah LiFePO4 battery ($799 sale, $949 regular), Renogy 100 W rigid panels ($157.70 for two, sale price), plus a charge controller, inverter, fuses and wire | Expandable, can feed wired lights and outlets | Needs code-compliant wiring and fusing, ideally by a licensed electrician, and possibly a permit and inspection |
| Power from the house | A circuit run from your main panel by an electrician | Unlimited run time, handles big tools | Trenching and permit costs; no power in a grid outage |
If your shed sits away from the house and gets better sun, it may also be a spot for a ground-mounted array, which our guide to ground-mounted vs roof-mounted solar covers.
Code and permit basics for a shed solar system
A shed system that is not connected to the grid is a stand-alone system under National Electrical Code Article 710, with solar wiring under Article 690 and energy storage systems over 1 kWh under Article 706. According to EC&M's summary of Article 710, premises wiring must meet the same requirements as similar installations supplied by a feeder or service, and the power sources must be identified by a permanent plaque or directory at each service equipment location.
Rapid shutdown rules in NEC 690.12 apply to solar systems on buildings. IAEI's review of the 2023 code notes an exception for non-enclosed detached structures and another for arrays not attached to buildings. A closed shed is an enclosed structure, so panels on its roof may need rapid shutdown equipment; ask your inspector which rules apply.
Before buying, DOE recommends checking with your building and zoning office, reviewing your deed for easements and checking HOA covenants. DOE also says approval is more likely if you follow the NEC, use pre-engineered packaged systems and submit complete plans with manufacturer diagrams. A portable power station that is not wired into the shed involves no premises wiring; wired lights and outlets are the part to discuss with your building department and to have a licensed electrician install.
Battery safety in a shed
Sheds get hot in summer and cold in winter, which affects batteries.
- Ventilation: DOE says batteries should be in a well-ventilated space, isolated from living areas and electronics, and protected from temperature extremes. Lead-acid batteries release hydrogen and oxygen while charging.
- Cold: Battle Born says LiFePO4 batteries should not be charged below about 25°F unless they have internal heating. In cold climates, use a heated battery or bring a portable unit indoors in winter.
- Heat: Battle Born says its batteries are typically rated to operate up to around 135°F, and that sustained high heat can speed up wear. Keep batteries out of direct sun and away from a hot metal roof.
- Protection: DOE lists safety disconnects, grounding and surge protection as standard equipment; Victron adds properly sized cables and DC fuses.
If a fuel generator is your backup, the Consumer Product Safety Commission says never use one inside homes, garages, basements, crawlspaces, sheds or other enclosed areas, even with doors or windows open, and to run it at least 20 feet from buildings.
Is solar for a shed worth it?
Solar makes sense for a shed when the load is light, the shed gets good sun, and running a cable from the house would mean long trenching or a panel upgrade. It makes less sense for a power-hungry workshop, a shaded yard or a shed used mainly in winter evenings.
On cost, there is no federal tax credit to count on: the IRS says the residential clean energy credit is not allowed for expenditures made after December 31, 2025, which for solar means an installation completed after that date. Compare the price of a small system against an electrician's quote for running a circuit, and think about how much you value having power in the shed during an outage.
Next steps
Write down every device you plan to use in the shed, total the watt-hours with the kWh calculator, and check each tool's watts and surge. Then choose between a power station and a component system, and call your local building department before wiring anything permanent. For a larger outbuilding, our off-grid cabin cost guide walks through bigger budgets.
Frequently asked questions
How much solar do I need for a shed?
Most hobby sheds need a few hundred watt-hours a day. A shed using about 340 Wh a day needs roughly 85 W of panels at 4 sun hours just to keep up, so 150 to 200 W gives a sensible margin.
Can a solar shed system run power tools?
Small tools used briefly usually work if they stay within the inverter's continuous and surge ratings. Large tools such as table saws and air compressors often need more inverter capacity and battery than a small system has.
What size battery do I need for shed solar?
Multiply daily watt-hours by the days of backup you want and divide by usable capacity. For about 340 Wh a day and two days of backup, plan on roughly 760 Wh of lithium or 1,360 Wh of lead-acid.
Do I need a permit for solar on a shed?
Often, especially for wired lights and outlets. Stand-alone systems fall under the National Electrical Code, and DOE recommends checking with your local building and zoning office before buying equipment.
Can I keep a solar battery in an unheated shed?
Yes, with care. DOE says batteries should be protected from temperature extremes, and Battle Born says LiFePO4 batteries should not be charged below about 25°F unless they have internal heating.
Sources
- U.S. DOE Energy Saver - Estimating Appliance and Home Electronic Energy Use
- U.S. DOE Energy Saver - Planning a Home Renewable Energy System
- U.S. DOE Energy Saver - Balance-of-System Equipment Required for Renewable Energy Systems
- EcoFlow - DELTA 3 Plus Portable Power Station
- Battle Born Batteries - 100Ah 12V LiFePO4 Deep Cycle Battery
- Battle Born Batteries - Understanding Temperature Limits of LiFePO4 Batteries
- Renogy - 100W/200W N-Type Monocrystalline Solar Panels
- Victron Energy - How to Size a Solar System for Your RV
- Victron Energy - SmartSolar MPPT 100/30 and 100/50 technical specifications
- EC&M - NEC Requirements for Standalone Power Production Systems
- IAEI Magazine - 2023 National Electrical Code and Photovoltaic Power Systems
- CPSC - Warns of Generator, Carbon Monoxide and Fire Hazards Ahead of Hurricane Season (May 2026)
- IRS - FAQs on modification of sections 25C, 25D and others under Public Law 119-21
- EC&M - NEC Requirements for Energy Storage Systems (Article 706)
Questions and comments
Be the first to ask a question or share your experience.